When I think of the phrase “Florida Weave,” it reminds me
of a hairdo you might get on a beach vacation to Florida. Actually, it has nothing to do with hair care
and everything to do with supporting indeterminate tomato varieties using a
trellising technique. In the past I’ve
used various methods including staking and tomato cages with little to no
success.
Since stumbling upon the Florida Weave trellising
technique on the Internet, I’ve never been tempted to even try another
method. Before I learned of this method,
my tomato vines were unruly, falling on the ground, and hard to find the fruit,
much less pick it. The Florida Weave
solved all those problems and I’m thankful to whoever came up with this idea.
Every year I post how to do it in the hopes of sharing
the technique with someone who doesn’t know about it. All you need is some T-posts and baling
twine. It is a small investment that yields
immediate results and pays for itself quickly.
Fortunately, I always have both T-posts and baling twine on hand.
The very first thing you want to do is get your t-posts
and sledge hammer (or t-post banger) and drive a t-post on either end of your
tomato rows. My rows are 24 feet long so
for extra support, in addition to having t-posts on either end, I drive a post
right in the middle of the row also.
Driving in the t-posts to create the skeleton of the Florida Weave |
Then about six inches off of ground level, I anchor some
baling twine to the t-post on one end and weave the twine in and out of all of
the tomatoes on the row in serpentine fashion.
In other words, after tying off at one end, you’d pass the twine around
the left side of the first tomato plant and then around the right side of the
second tomato plant, and so on and so forth until you get to the end of the
row.
Then, you would alternate sides coming back to the
original t-post you started from, passing the twine on the opposite side of the
tomato plant that you placed the twine on the first pass. It is important to keep the twine pulled very
tight. The twine hugs the tomato plant
tightly on either side, creating a supporting structure that keeps the vining
plant upright and off the ground.
Baling Twin hugs the tomato plant and keeps it upright and erect |
Pardon all the weeds that are in the garden. These will be covered with a thick mat of
mulch soon. I wanted you to see an
example of the support structure of the Florida weave after the first level.
A look at the Florida Weave after the first level of twine is in place |
Your work is not done, though. Keep a close eye on your tomatoes as soon it
will be time to put in the second level of trellising. After a few days, your tomato plants will
have grown another six inches and it will be time to repeat the process, only
six inches (or whatever desired length) up from the first level. I’ve shown the second level of trellising
below. Note the tautness of the twine
and how I’ve wrapped the twine tightly around the t-posts. As your plant grows and puts on fruit, it
will be heavy and require a firmly fastened support structure, sort of like the
cables on the Golden Gate Bridge.
The Second Level of Twine |
As you can see below the tomatoes continue to grow and it
will soon be time to put the third level of trellising up. You just keep repeating the process as the
tomato grows.
Almost ready for level #3! |
Sooner or later, though, the height of your tomato plant
will exceed the height of your t-posts and the top of the vine will spill over
into the row, making it hard to walk and harvest tomatoes. In using this technique a few years, a friend
suggested an expensive, easy solution to this problem. Using lengths of rebar or ¾ inch conduit and
hose clamps to fasten it down to the t-post, you simply extend the height of
the t-post upward by several feet to accommodate the additional growth, adding
more levels of baling twine.
Florida Weave. I
give this technique a 5 star recommendation and two thumbs up! Compared to other techniques, the Florida Weave is a dream.
No comments:
Post a Comment